Plasma Pancake Coil by @cahlen on 3Speak
The Pancake Coil is an alternative way that the Plasma Machine can be used rather than the standard dual CFL Bulbs most people are familiar with. --- ▶ Watch on 3speak.tv
Tags: #technology #health #diy #science #tesla #future #biohacking #life
Hey everyone, Callan here, and in this video I'm going to be making my first pancake coil for the plasma machine. So many of you who are familiar with the plasma machine, I've made lots of videos about it. You've seen it's usually using those twirly CFL bulbs, and you hold onto both bulbs and move them around, different parts of your body. But there's actually another way that you can use this machine. and one of them is with a pancake coil, okay? So you're going to have basically big spiral of two different wires, which connect to each other in a certain way at the end, which connect to the red part where the bulb would plug in to the red wire, okay? Then you're going to have the black wire go to an actual ground, a grounding rod that goes down into the earth. And this is something that you would sit on or stand on. for maybe, you know, 15, 20, half an hour, maybe even an hour at a time. And I don't know much about what kind of effects you get out of it, but I know that the person who designed this thing, Christian Amenethus, Marino, would treat people by first having them come in and stand on this thing for like 45 minutes, and then he would get out the bulbs, which in the bulbs. and focus on specific areas of the body, but he considered the pancake coil to be an extremely important element of it, okay? So anyways, I'm going to be building my own today. It's basically based on, I don't know what Tesla called it, but it's based on a coil which he made, which is, it's a big topic, but it's a very advanced piece of coil, so a way of wrapping wire, a very specific way I'll show on the screen, what it looks like. It can be used for all kinds of different things. For example, it can even replace a capacitor. And the way it works is, for those you know what induction is, the current is going in, and it's wrapping around. Okay, so you're stirring up the magnetic field, and then it gets to the outside, and it connects to another wire, which then goes back into the middle of the coil again and wraps the exact same way. So you're basically doubling up, or maybe even... you know, exponentially increasing the impact of induction on the magnetic field, okay? So the current increases the magnetic field spin, and the magnetic field spin increases the current, and you're doing that with two different wires on basically the same electrical line, right? But because of the way that this thing is wired up, that's not actually quite what's happening. But anyways, I won't go too deep into that, but I will show you how to make it and how to wire it up. So here's what it looks like while I'm wrapping it. I'm just on this big square plywood board. There's a hole drilled right in the middle, which I stick the two wires down, and I have about a foot and a half to two feet of wire going down there because I'm going to need to bring that wire all the way across on the other side. Then it just wraps around every other one, and there's a total of 14. You can see there is tape here, which is sticky side up. That's what makes it easier to wrap this. It's still hard to wrap this even with this, but if I didn't have tape, it would be near impossible to keep everything in the right position while I'm wrapping it. Okay, so you're going to have the two ends that go down the center. They're going to come across, and then you're going to have the two ends that come off the side, and I'll show you how these all connect after I wrap this whole thing with tape. Okay, so I'm going to put tape on the top of this to hold it even more secure and wrap it up, and it's just going to be a big black circle. Okay, this is what it looks like with another layer of tape facing sticky side down now. So we've got a sticky side facing up on the bottom side and a sticky side facing down. So this thing's pretty secure now. So I'm just going to cut this off, and then I'm just going to cut around this thing to make the final shape. You can see we've got the wires coming off here. And we've got the two wires coming out the hole in the middle. This is the bottom side where the wire came out. Okay, so now the wire is... coming up across the actual wrappings and it's going to come out the same side that these are coming out because we're going to need to connect these together. Next, I'm going to just cut this just to give us so this stuff isn't in our way while we're connecting things. So this is my first attempt at this, and I'm just showing you the process, but I did make a mistake. the red wire, or whatever you're central, so whatever the one that starts in the very center here, which for me is the black wire coming across here, you need to have the opposite one being the last one on the outside, okay? So I had this black wire going around another time, and that was not correct, so I needed to cut around the edge and pull this around so that it was actually second to last, okay? So at this point, I'm going to connect the outside wire, which for me is the red wire, to the first wire at the center of the coil, which comes across here on the other side. You're just going to connect these together real close here, okay? Because basically, they're just a continuation of the coil. And then the other two, now if you're going to use this for other purposes, these would be completely separate. You would not connect them together. but we're going to connect them together for the purpose of the plasma machine, and these are just going to connect into where the bulbs would usually go. Okay, so I've got it all wired up correctly. I'm going to show you it in action. You can see, you combine these two down into one wire, and it goes down into a banana plug, which is where I would normally plug in the light bulb, so I can swap in the light bulb for this thing instead. and then it goes to the black hole coil of the machine. Now, the other side where you would have the other bulb, it is going to a banana plug, but that banana plug goes down here into the ground, where there is a rebar, about two and a half feet long, which is dug or pounded down into the ground. Now, I'm going to get like a four -foot long copper grounding rod, which I'm going to pound into the ground over here, probably tomorrow or something like that. I think it gets here then. But for now, I'm just using the rebar as the ground. So normally with the bulbs, you would have the actual current going through your body because you're holding both bulbs. There's no ground. But with this setup, you need the black wire to be going to ground, and you're only exposing yourself to the red. So now I'm going to turn off the lights and show you what this looks like when I start touching it. Now, when you touch it, you need to make sure that you are not touching anything metal or that you are not touching the ground. If you're touching the ground, that black wire is going to connect the circuit to you through the actual ground. So if I'm touching this thing and then I touch the ground anywhere, I'm going to see sparks come into my finger. Or if I touch anything metal like this... this metal nail right here, I'm going to see sparks go from my hand into that thing. Or even if I touch this ceiling, I'm going to see sparks go into it if I'm touching that thing, okay? So you don't want to be touching any metal, and you don't want to be touching the ground. Okay, I got my tripod set up with my phone, a fair distance away. I'm zoomed in a little bit, and I'm going to turn off the light and then turn on the machine so that you can actually see what's happening. So anyways, here's the last look at it. You know, it's about maybe a little more than a foot wide. You know, it's extremely lightweight. It's a little bit flexible, so I wouldn't want to, you know, push it too much because the wires might come out of alignment with each other. And, you know, this is my first one, so it's a little bit janky. Not the most beautiful thing, but I think future ones that I make will probably be a better quality. So anyways, if I ever do end up... making and selling my own plasma machine, then this might be something that comes with it. I know Hillbilly sells his with, I think maybe he sells it with two. I think maybe he recommends using it in a different way than what is advised. Like, for example, the official recommendation is that the black wire needs to go to a grounding rod and that you're touching this. and this is the only thing that you're touching, but I know other people who have used this and then had the black one go to a light bulb and be using that, and even having, you know, this and a light bulb plugged into the red, and then, you know, I think maybe even another pancake coil and a light bulb on the other side. So there are other things that you could technically do, but no one really understands how this thing works, okay? We just know that, when you use in the way that people, that is recommended by a manifest, it is extremely beneficial, but no one really understands why, okay? So when we start deviating from what was recommended, you know, we don't know whether that's safe or not, okay? So, I mean, technically you could do that, but I personally think it's better to stick. to what was recommended, at least until I understand what's going on, which may never actually occur. So, anyways, that's the pancake coil. Thanks for watching, and I'll see you guys later.